SF1062 211 mhz saw filter rf monolithics, inc. phone: +1(972)233-2903 european sales office 4347 sigma road fax: +1(972)387-8148 44 1 96 3 25 13 83 dallas, texas 75244 e-mail: info@rfm.com 44 1 96 3 25 1 51 0 usa home page : www.rfm.com SF1062.doc 7/28/1999 d electrical connections (see note 3) connection terminals port 1 hot 1 port 1 gnd return 2 port 2 hot 8 port 2 gnd return 9 no connection 7, 14 case ground all others absolute maximum ratings rating value units maximum incident power in passband +10 dbm max. dc voltage between any 2 terminals 30 vdc storage temperature range -40 to +85 c max soldering profile 265 c for 10 s designed for gsm pcs receiver if applications simple external impedance matching hermetic metal dip unbalan ce d input and output characteristic sym min typ max units notes nominal center frequency fc 211.000 mhz il 6 9.0 db 1 bw 1 .5 50 bw 2 80 bw 3 100 135 khz gdv 80 500 ns p -p passband insertion loss at fc 1 .5 db passband 2 db passband 3 db passband group delay variation over fc 50 khz absolute group delay gd 5000 ns 1, 2 5 25 30 35 rejection fc-400 to fc-200 and fc+200 to fc+400 khz fc-600 to fc-400 and fc+400 to fc+600 khz fc-800 to fc-600 and fc+600 to fc+800 khz 19 1 mhz to fc -800 khz and fc +800 khz to 231 mhz 35 45 db 1, 2, 3 operating temperature range t a -10 +70 c 1 impedance matching to 50 w unbalanced external l-c case style dip14l-8 22.1 x 12.6 mm nominal footprint lid symbolization ( yy = year, ww = week) rfm SF1062 yy ww notes: 1. unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 w and measured with 50 w network analyzer. 2. unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. 3. rejection is measured as attenuation below the minimum il point in the passband. rejection in final user application is dependent on pcb layout and external impedance matching design. see application note no. 42 for details. all ?nc? or ?no connection? terminals should be grounded. 4. ?lrip? or ?l? after the part number indicates ?low rate initial production? and ?eng? or ?e? indicates ?engineering prototypes.? 5. the design, manufacturing process, and specifications of this filter are subject to change. 6. either port 1 or port 2 may be used for either input or output in the design. however, impedances and impedance matching may vary between port 1 and port 2, so that the filter must always be installed in one direction per the circuit design. 7. us and international patents may apply. 8. rfm, stylized rfm logo, and rf monolithics, inc. are registered trademarks of rf monolithics, inc. 9. ? copyright 1999, rf monolithics inc. 10. electrostatic sensitive device. observe precautions for handling.
SF1062 211 mhz saw filter rf monolithics, inc. phone: +1(972)233-2903 european sales office 4347 sigma road fax: +1(972)387-8148 44 1963 251383 dallas, texas 75244 e-mail: info@rfm.com 44 1963 251510 usa home page : www.rfm.com SF1062p 0 db -20 -40 -60 -80 -100 0 db -2 -4 -6 -8 -10 2.5 mhz/div 100 khz/div 200 ns/div
rf monolithics, inc. phone: (972) 233-2903 fax: (972) 387-8148 e-mail: info@rfm.com rfm europe phone: 44 1963 251383 fax: 44 1963 251510 http://www.rfm.com ?1999 by rf monolithics, inc. the stylized rfm logo and rfm are registered trademarks of rf monolithics, inc. dip14l-8 dimension mm inches min nom max min nom max a 22.10 22.50 0.870 0.886 b 12.55 13.00 0.494 0.512 c 3.56 3.81 0.140 0.150 d 0.41 0.48 0.51 0.016 0.019 0.020 e 0.89 0.035 f 7.62 0.300 g 15.24 0.600 k 3.30 3.81 6.73 0.130 0.150 0.265 l 1.37 1.45 1.52 0.054 0.057 0.060 p 2.54 0.100 r 1.60 0.063 metal 8-pin dip in 14-pin (long) configuration 22.1 x 12.6 mm nominal footprint dip14l-8 case d (8 places) b a e pin 1 mark (optional) (4 places) l c k f r (3 places) g p (4 places) 1 2 6 7 8 9 13 14
|
